meta data for this page
  •  

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
wiki:software:software:smartpltlive:setup:assigntargetstolanes [2021/03/11 08:09]
frhs 		wiki:software:software:smartpltlive:setup:assigntargetstolanes [2021/03/11 08:35] (current)
frhs
Line 4: Line 4:
  
 SmartPLT Live manages a list of targets and devices it can find in the network. But with this information the target can't know what target is which lane in your shooting range. You need to assign each of your phisical targets to a lane to tell SmartPLT Live which Target represents which lane. SmartPLT Live manages a list of targets and devices it can find in the network. But with this information the target can't know what target is which lane in your shooting range. You need to assign each of your phisical targets to a lane to tell SmartPLT Live which Target represents which lane.
 +
 +**SmartPLT Live One:** As SmartPLT Live One is made for usage with only one target at the same time, you dont need to assign the targets manually. Each time a target is detected in the network and you make a shot on the target, the Target is assigned automatically to the only lane in the Lane list. So you don't take care about assiging your target to a lane.
 +
 +**SmartPLT Live Competition:** In SmartPLT Live Competition you need to assign the targets to the lanes. This could be done in different ways (see below). After the correct assignment you can save you configuration into a file on your computer. Later you dont need to do the assignment again. Just reload the Range Configuration file and you can are done with the setup.
  
 ===== Where I can find the Lane List? ===== ===== Where I can find the Lane List? =====
 +
 +You can find the Lane List in SmartPLT Live unter the "Range Setup" page.
 +
 +{{:wiki:software:software:smartpltlive:setup:pasted:20210311-081702.png}}
 +
 +===== How to Assign the Targets to the Lanes? =====
 +
 +==== Manually ====
 +
 +You can easily drag and drop the targets from your target list onto lanes in your lane list. The target will be immediately assigned to the lane. If you dont have lanes in the list where you can drop the target onto, easily click the "Add Lane" button.
 +
 +==== Automatically by using the "Fast Range Config Mode" ====
 +
 +The "Fast Range Config Mode" is a helper procedure to help you with the setup of your shooting range.
 +
 +You need to follow the following steps to assign your target to your lanes:
 +
 +1.) Start the Fast Range Config Mode by clicking the "Fast Range Config Mode"-Button in the menu bar.
 +{{:wiki:software:software:smartpltlive:setup:pasted:20210311-083011.png}}
 +
 +2.) SmartPLT Live Competition may aks you if you really want to clear the actual configuration. Klick Yes.
 +
 +3.) Start with the Frist Target in your shooting range and make one shot on this target. SmartPLT Live should automatically assign this target to the Lane 1. If the Lane 1 does not exist the Lane 1 is created. 
 +If you have ShotLight Lamps, the Lane will answer with a blinking pattern on the lamp to configm that the target is registered in the configuration
 +
 +4.) Go through all the Lanes and make one shot on each target. Each target should confirm that its registred correctly by showing the blinking pattern on its ShotLight Lamp.
 +
 +5.) After you went thorugh all the Lanes in your Shooting range, click the "Fast Range Config Mode" button again to finish the Fast Range Config Mode.
 +
 +6.) Save your Range Configuration by clicking Save as in the menu bar.
 +
 +When you start SmartPLT Live the next time, this saved file will be automatically reloaded.